Gelco Chimney Inspection Nationwide

Gelco Chimney Inspection in Dallas: What to Know First

We inspect Gelco chimney systems across Dallas with a straightforward approach: a written price before we touch anything, a camera inspection you can watch, and a plain-spoken report of what’s actually wrong. Most Gelco inspections run between $189 and $349 depending on the level, and we’ll tell you the number up front. If you own a Gelco factory-built fireplace or chimney system and haven’t had it looked at in a while, call (361) 314-3193 and we’ll walk you through what to expect before we even book the truck.

Call (361) 314-3193

This page is for Dallas homeowners who have a Gelco fireplace, Gelco chimney, or Gelco venting components and want an inspection they can trust, from a company that doesn’t sell work that isn’t there.

How Gelco Products Fail – and How We Fix Them

Gelco made factory-built chimney systems and components that show up in a lot of 1980s and 1990s homes around Dallas, especially in East Dallas, Richardson, and Garland. We see them often enough to know their repeat failure patterns. Here’s what we typically find:

• Gelco double-wall air-cooled chimney sections with separation at the flue joints. These chimneys rely on a precise air gap between the inner flue and outer casing. After decades of Dallas heat cycling, the sections can shift, especially at the mid-roof joint where the chimney passes through the attic. We verify joint integrity with a camera run, and when separation is caught early, we can reseat and secure the section rather than replace the whole run.
• Gelco moisture intrusion at the chimney chase top. Many Gelco installations used a galvanized chase pan that rusts out at the corners after 20-plus years of North Texas storms, then lets water run down inside the chase. By the time a homeowner sees staining on the ceiling, the chase interior has already been damp for a while. We inspect the chase top and flashing as part of every Gelco Level 2 inspection, not just the flue.
• Refractory panel cracking inside Gelco factory-built fireboxes. The firebox liners on older Gelco units are made of a refractory panel material that looks like cement board. It can develop hairline cracks from normal expansion, but larger cracks that expose the metal shell are a sign the unit needs a closer look. We photograph these cracks during the inspection so you can see exactly what we mean before any repair is suggested.
• Gelco termination caps with damaged spark screens. The cap on a Gelco chimney is the first thing the weather hits, and Dallas hailstorms are rough on spark screens. Once the screen is torn or missing, you can get birds building inside the flue, and in the spring we see that a lot. Cap replacement is usually quick and the parts are readily available.
• Listed clearances compromised by later renovation work. This one isn’t Gelco’s fault, but it’s a pattern in Dallas. An older home gets a remodel, sheetrock is added, a built-in goes in around the fireplace, and suddenly the original clearances required for a Gelco factory-built system are no longer met. We check clearances against the Gelco listing plate, which is still on many of these units, and tell you plainly what’s safe and what needs correction.

Our Gelco Chimney Inspection Process

Every Gelco inspection we do in Dallas follows the same steps, so you’ll know exactly what’s happening and why:

1. 1
   You call (361) 314-3193, a live person answers. We schedule a day that works, and we give you a real arrival window. No call center, no voicemail loop.
2. 2
   We arrive, look, and quote the inspection price in writing. Before we open a tool bag, you have the number. If the inspection leads to repair work later, that price also comes in writing before any work begins.
3. 3
   We locate and read the Gelco listing plate. This tells us the model, the clearance requirements, and what the system was tested for. If the plate is missing, we’ll note that in the report.
4. 4
   Camera inspection of the full flue from top to bottom. We don’t rely on a flashlight and a mirror. You can watch the screen with us if you like, and we record images for the report.
5. 5
   Complete Level 1 or Level 2 inspection per the current NFPA 211 standard. For real estate transactions or after a weather event, a Level 2 is usually what’s required for a Gelco system in Dallas.
6. 6
   Written findings, plain-Dallas-English explanation, and a written quote for anything we recommend. If it can wait, we’ll say so. If it can’t, you’ll see the reason in the camera images, not just our word for it.

What Gelco Chimney Inspection Costs in Dallas

Here’s the price honesty we lead with, because that’s the whole point of how we work:

What moves the price on a Gelco inspection in Dallas is mostly access: roof pitch, chase height, and whether the inspection is a standard Level 1 or a full Level 2 with attic access. Second stories and steep pitches add time, and we’ll tell you that before we start. Call (361) 314-3193 for an exact quote. Estimates are free.

Why Dallas Homeowners Call Ashby Chimney Dallas for Gelco Work

Because a lot of them already tried the other route: a company that never showed up, or a quote that doubled after the technician got on the roof. We’re built differently, and Nathan Corliss runs this Dallas shop with that in mind. The Kingswell Guarantee sits behind every Gelco inspection and repair we do, and it means what it says: written price before any work begins, written guarantee on every repair, and if a covered repair fails, we come back and fix it at no charge. That’s the 365-Day Done Right Promise. We also stock and source professional-grade materials from established chimney-trade brands including DuraFlex and HeatShield alongside Gelco components, so if your Gelco system needs a liner section, a cap, or a refractory panel, we’re not running to the hardware store hoping something fits.

Frequently Asked Questions